This page is for study. Please confirm important details against the original standards and vendor documents.
Study reference
Cisco Commands Cheat Sheet
Common Cisco commands for network engineers, grouped by task, with placeholders only.
1. Modes and saving
Router> user EXEC mode
Router> enable
Router# privileged EXEC mode
Router# configure terminal
Router(config)# global configuration
Router(config)# interface GigabitEthernet0/1
Router(config-if)# interface configuration
Router(config-if)# end back to privileged EXEC
Router# copy running-config startup-config save the configuration
Router# show running-config what is running now
Router# show startup-config what loads at boot
2. Everyday show commands
| Command | Shows |
|---|---|
show version | Software version, uptime, model, memory |
show ip interface brief | Interface addresses and up or down status |
show interfaces status | Port status, speed, duplex and VLAN (switches) |
show interfaces GigabitEthernet0/1 | Detail and error counters for one interface |
show vlan brief | VLANs and the ports in them |
show interfaces trunk | Trunk ports and allowed VLANs |
show mac address-table | MAC addresses the switch has learned |
show ip arp | IP to MAC address mappings |
show spanning-tree | Spanning tree roles and states |
show etherchannel summary | Port-channel status |
show cdp neighbors detail | Directly connected Cisco devices (show lldp neighbors for LLDP) |
show ip route | The routing table |
show access-lists | Access lists and match counters |
show ip nat translations | Active NAT entries |
show logging | Recent log messages |
show processes cpu sorted | What is using the CPU |
3. Interface and VLAN basics
interface GigabitEthernet0/1
description Link to core switch
ip address 192.168.1.1 255.255.255.0
no shutdown
vlan 10
name SALES
interface GigabitEthernet0/2
switchport mode access
switchport access vlan 10
interface GigabitEthernet0/24
switchport mode trunk
switchport trunk allowed vlan 10,20
! Some older multilayer switches first need:
! switchport trunk encapsulation dot1q
4. Inter-VLAN routing
! Multilayer switch: one SVI per VLAN
ip routing
interface Vlan10
ip address 192.168.10.1 255.255.255.0
no shutdown
! Router on a stick: one sub-interface per VLAN
interface GigabitEthernet0/0.10
encapsulation dot1Q 10
ip address 192.168.10.1 255.255.255.0
5. Spanning tree, EtherChannel and port security
spanning-tree mode rapid-pvst
spanning-tree vlan 10 root primary
! Access port to a PC: fast start, protect against switches being plugged in
interface GigabitEthernet0/3
spanning-tree portfast
spanning-tree bpduguard enable
switchport port-security
switchport port-security maximum 2
switchport port-security violation restrict
switchport port-security mac-address sticky
! LACP EtherChannel
interface range GigabitEthernet0/1 - 2
channel-group 1 mode active
interface Port-channel1
switchport mode trunk
6. Routing (short forms)
ip route 0.0.0.0 0.0.0.0 192.168.1.254
router ospf 1
router-id 1.1.1.1
network 192.168.10.0 0.0.0.255 area 0
router bgp 65001
neighbor 203.0.113.2 remote-as 65002 More detail is on the routing, OSPF and BGP sheets.
7. Access lists and NAT
! Named extended ACL. Rules are checked top to bottom, and there is an
! implicit "deny all" at the end, so end with a permit if you need one.
ip access-list extended BLOCK-TELNET
deny tcp any any eq 23
permit ip any any
interface GigabitEthernet0/1
ip access-group BLOCK-TELNET in
! Allow only one network to manage the device over SSH
ip access-list standard MGMT-ONLY
permit 192.168.10.0 0.0.0.255
line vty 0 4
access-class MGMT-ONLY in
! NAT overload (PAT) for an inside network
interface GigabitEthernet0/0
ip nat inside
interface GigabitEthernet0/1
ip nat outside
access-list 1 permit 192.168.10.0 0.0.0.255
ip nat inside source list 1 interface GigabitEthernet0/1 overload
8. DHCP
ip dhcp excluded-address 192.168.10.1 192.168.10.20
ip dhcp pool SALES
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 192.0.2.53
9. Basic device security
hostname R1
enable secret <choose-a-strong-password>
username admin privilege 15 secret <choose-a-strong-password>
ip domain-name example.local
crypto key generate rsa modulus 2048
ip ssh version 2
line vty 0 4
login local
transport input ssh
service password-encryption
banner motd # Authorised use only # Prefer secret over password. service password-encryption only lightly hides older passwords and is not strong protection. Never put real passwords in notes or screenshots.
10. Testing and troubleshooting
ping 192.168.1.2
ping 192.168.1.2 source GigabitEthernet0/1
traceroute 192.168.1.2
terminal length 0 show long output without paging
! Debug output can overload a device. Use only briefly, and switch off after.
debug ip ospf adj
undebug all A sensible order: Layer 1 (cable, link lights, interface up), Layer 2 (VLAN, trunk, MAC table), Layer 3 (address, mask, gateway, route), then ACLs, NAT and the application.
More cheat sheets
- Networking Cheat Sheet
- Routing Cheat Sheet
- OSPF Cheat Sheet
- BGP Cheat Sheet
- SDN, SD-WAN and SASE Cheat Sheet